2010 mac mini upgrade hard drive

Your current drive if it's still functional can be backed up using a program like Apple's Time Machine or the free utility SuperDuper. The cover on the Mac Mini is held in place with small clips that must be dislodged with the putty knife.

Mac Mini Mid SSD Installation - Crucial

Gently shimmy the knife in between the base of the Mac Mini and the case. Bend the knife away from you as you slowly work your way around all fours edges of the device. You will hear a faint pop as the clips become dislodged, at which point the cover can be lifted off. Next, you have to remove the three antennas. The two smaller ones on the left simply lift out, while larger one on the right must be squeezed from the bottom. Under each antenna are springs -- don't lose these as they are required when reassembling the device. For now, place them aside. The hard drive is located on back of the CD drive.

Unscrew the four screws that hold the CD drive into place and detach the ribbon cable on the top of the drive. Make sure you are removing the screws that connect the drive to the case and not the ones on the actually CD drive. The hard drive is on the back of the CD drive. It's held in with four screws, two on the top and two on the side. There is a temperature sensor on the top of the drive and a wire running down the left side. Gently lift the sensor, move the wire to the side, slide the drive up slightly, and remove it using the tweezers. There are two anti-static cushions on the back of the hard drive, peel both of these cushions off of the old drive and place them onto your new one, which you can then slide into the slot.

Flags 0. Introduction Use this guide to completely replace your mini's hard drive.

Upgrade or install memory in your Mac mini

Step 1 Bottom Cover. Add a comment. Add Comment. Step 2. Step 3 Fan. Step 4. Step 5. Step 6 Cowling. Step 7. Step 8 Antenna Plate. Step 9.


  • What RAM Should You Get?!
  • Choose your model.
  • How to Install a Hard Drive in the Apple Mac mini (.

Step Step 12 Hard Drive. Step 18 SSD Installation.

Mac mini Mid 2010 Hard Drive Replacement

Almost done! To reassemble your device, follow these instructions in reverse order. Completing this guide requires rubber cement to stick the old thermal sensors to your new hard drive. Buy these tools.

If you care what I had for breakfast

Buy these parts. Rotate the bottom cover counter-clockwise until the white dot painted on the bottom cover is aligned with the ring inscribed on the outer case.

How to Upgrade/Replace the Drives in a Mac mini Server 2010 (Updated)

Remove the two Lift the ear of the fan nearest the RAM up off the standoff secured to the outer case. If the fan doesn't separate from the standoff screw with a moderate amount of force, you can use a T6 Torx driver to simply remove this screw. Carefully pull the fan cables upward to lift the fan connector up out of its socket on the logic board. Carefully pull the antenna plate straight away from the circular rim of the outer case. Do not remove the antenna plate yet. Carefully pull the wires for both hard drive thermal sensors upward to lift their connectors up and out of their respective sockets on the logic board.

OWC Mercury Electra 3G

Use the flat end of a spudger to pry both the hard drive and optical drive connectors up out of their sockets on the logic board. For enough clearance to remove the hard drive, the logic board must be slightly removed. To accomplish this, two cylindrical rods must be inserted into the holes highlighted in red.

Inserting instruments into any logic board holes other than the ones highlighted in red may severely damage the logic board. Be sure it makes contact with the outer case below the logic board before proceeding. If you don't have a Logic Board Removal Tool handy, you can use two tools having a maximum diameter of 2. Just insert one into each of the highlighted holes.


  • shortcut for new folder on desktop mac.
  • Introduction.
  • mac mail slow sending email;
  • Apple - USE TAG.
  • Before you begin;
  • how to record game on mac.

Remove the Mac mini Logic Board Removal tool. Pulling the assembly out further may damage the IR sensor connector highlighted in red in the third picture. Lift the hard drive from the edge nearest the logic board and remove it from the mini, minding the RAM socket and any cables that may get caught. When reinstalling the hard drive, be sure the two T8 Torx lugs on its far end are inserted into the two rubber grommets highlighted in red in the second picture before sliding the logic board back into place.

Remove the hard drive cable by pulling its connector straight away from the hard drive. Remove the piece of tape covering the thermal sensor attached to the edge of the hard drive. If you are installing a new hard drive, we have an OS X install guide to get you up and running. I did not complete this guide. These instructions and a little common sense can also be used to replace the lower hard drive in the server version of the Mac Mini.

Luckily that was the drive that had failed in my case.